Fixed: Xhorse MVCI PRO J2534 Sync Failed Error Code: ff02

 Problem: I've updated XHORSE MVCI PRO J2534 firmware and software to latest, but I am still getting the attention: "Sync authorization 2 failed! Error code: ff02". The firmware is 1.20 and software is 2.0.1.

What's the problem?

Fixed Xhorse MVCI PRO J2534 Sync Failed Error Code ff02

Fixed Xhorse MVCI PRO J2534 Sync Failed Error Code ff02

Solution

Please go for synchronization firstly:

Device management >> Connect >> Read authorization >> Update authorization

Fixed Xhorse MVCI PRO J2534 Sync Failed Error Code ff02

The problem will be solved.

Technical Support

www.xhorsestore.co.uk

Comments

Post a Comment

Popular posts from this blog

Xhorse VVDI PROG with DB15 cable read Porsche BCM 2M25J

Image
 I finally got the new XDPGSOGL DB15 Cable to realize working with VVDI PROG & Xhorse Porsche Adapter . This is the first time to test reading the Porsche BCM 2M25J and give a review. Since I have already opened the BCM and insert a solder-free adapter on it. Very convenient without any soldering. Only to refer to the connection diagram in VVDI PROG . Be careful with those points marked in red. Test Backup Review Start VVDI PROG software to select options at first: Type: 4 IMMOBILIZER, Brand: Porsche, Chip: BCM-2M25J-BACKUP(ADAPTER) Click "Read", it reads correctly. Then save the D-Flash file. It's always safe to make a backup. Backup D-Flash OK. Now let's read P-Flash… Reading success. It takes longer time to finish. Save the P-Flash file. Backup P-Flash OK. Unlock & Lock BCM Review Select chip to: BCM-2M25J-R/W/UL(ADAPTER) Read ID OK . C482 is the Porsche processor that I have. Read Partition, it says "Chip is crypt. This ...
Read more

Xhorse VVDI Key Tool Plus AKL programming for Audi A4 2013

Image
  Xhorse VVDI Key Tool Plus Pad can program Audi A4 2013 all keys lost by OBD successfully. Xhorse also developed Audi BCM2 Solder-free Adapter for programming 2013-2019 A4L, A5, Q5, A6L, A7, A8 on bench.   It'll need to select "Prog read - encrypted BCM2" instead of "Read by OBDII" on tablet. As I don't have those Audi BCM2 adapters, I'll go on using OBD method. It may help: How Audi BCM2 Solder-Free Adapter Works with Xhorse Key Tool Plus? http://blog.xhorsestore.co.uk/xhorse-adapters-and-parts/how-audi-bcm2-solder-free-adapter-works-with-xhorse-key-tool-plus/   Procedure Connect VVDI Key Tool Plus into OBD2. The steps including read & save BCM data, make dealer key & key learn.   Read & Save BCM Data Immo programming >> Europe >> Audi >> Select by type >> Fifth immobilizer system >> Start programming >> Read BCM data >> Read by OBDII >> Read BCM2 data (OBDII)   Ins...
Read more

Xhorse VVDI Key Tool Max PRO Clone Universal Remote Key

Image
 Hello, I'm here to show how to quickly clone an aftermarket remote with Xhorse VVDI Key Tool Max PRO programmer . This is the new key to be cloned, it's a Wired Remote comes from Xhorse. Preparation As it's a wired remote, you have to open key shell and take out the circuit board. I usually use a lighter to do it. Take out circuit board, don't put any battery on it. Connect the Universal Remote Key board to VVDI Key Tool Max PRO via cable. Now, let's start! Clone Remote Hold the working key. Go to Remote clone >> Special clone >> Start clone Just follow the prompts to operate: Press Lock button. Press again Lock button. Press Unlock button. Press again Unlock button. Press Trunk button. Press again Trunk button. Press Panic button. Press again Panic button. *If verification failed, just try re-acquisition again. *If the button is not required, press "Skip this button". Confirm the frequency: 433.92MHz, 184bps. ...
Read more