Xhorse VVDI Key Tool Max add key for 2017+ Honda SH Moto

Xhorse VVDI Key Tool Max programmer is able to add a new smart key for 2017+ Honda SH Moto successfully. Works on XSMQB1EN Smart Remote, easy programming in 3 minutes.

Honda SH Moto add key used Xhorse VVDI Key Tool Max

Place Xhorse smart key into Key Tool Max coil,

Vehicle remote >> Honda >> SH >> SH(2017+) Moto KeylessGo ID47 >> Generate remote

Wait it processing until 100%…

Burn success.

Honda SH Moto add key used Xhorse VVDI Key Tool Max

Honda SH Moto add key used Xhorse VVDI Key Tool Max

Honda SH Moto add key used Xhorse VVDI Key Tool Max

Honda SH Moto add key used Xhorse VVDI Key Tool Max

Turn ignition off then on.

Press LOCK or UNLOCK button on smart key to match.

Turn ignition off then on twice.

Test the new key.

It can work normally.

Done.

Honda SH Moto add key used Xhorse VVDI Key Tool Max

Honda SH Moto add key used Xhorse VVDI Key Tool Max

This is how to program a Xhorse Universal Smart Remote for 2017+ SH Moto with VVDI Key Tool Max. More VVDI Remotes for other car models, please consult online service.

Comments

Post a Comment

Popular posts from this blog

How to open Xhorse VVDI Remote Key to replace battery?

Image
 These are 2 Xhorse proximity VVDI Remotes with orange packing, both are XS series smarty remote. Next, I'm going to show how to open them to replace the battery.   Open XSKF01EN Universal Smart Key Cover This is a smart key with 3 buttons: lock, unlock, trunk. Press the upper right corner button to snap out top cover. Use a flat screw-driver to lever the backside cover along its edge. Take out the back cover, you can see a circle position. That's actually the position to put battery. Reinstall the cover to press any button. If the indicator flashes, which means done. The battery is installed correctly Open XSCS00EN Smart Remote Key Cover It's a shiny key with 4 buttons: lock, unlock, trunk, alarm. Press the button on upper backside to remove top cover. Use a knife & flat screw-driver to pry the cover along its edge line. Open the cover to take out circuit board. You can see battery slot is right on its backside. Put a battery in, then ...
Read more

Xhorse VVDI Key Tool Max failed to read XM8A key transponder

Image
I tried to use XM 8A Smart Key for a RAV4 2015 with 312.10-313.10 MH frequency. Xhorse VVDI Key Tool Max failed to read transponder after inserting original key and tells it’s unclonable.   It’s just work able to start engine or touch start button with the key, remote functions do not work. Is any optionson Key Tool Max for this dual frequency? XM Key is 8A transponder and is it possible to learn it to the car?   Tips from Engineer Check if the password bits of original chip & XM 8A chip are same; Check if the frequency of original chip & XM 8A chip are same; Remove original key battery when matching; Touch original key firstly until hearing beep once. Then finish to touch XM Smart Key(with battery) within 5s. Observe if indicator flashes when taking away: if yes that means OK, if no that means to be matched again.   Or Change Key Frequency on VVDI Key Tool Max path: Special function >> VVDI remote function/ VVDI smart key customizati...
Read more

How to Disassemble & Install Xhorse XM38 Smart Key?

Image
 This is a quick demo to guide how to disassemble & install Xhorse XM38 Universal Smart Key . Follow the tips to learn how to do. Check the operation video: https://www.youtube.com/watch?v=DOkDgCMjIBo How to disassemble XM38 Smart Key? Press & hold the button on the right side of the XM38 remote key and take out the upper cover. Use a screwdriver to slide the edge gap of the XM38 smart key, lift the side edge slightly downwards Finally lift the back cover completely. Disassembly is completed. Installation Install the battery and test whether the indicator light of the XM38 Remote Keyis on. After confirming all above is correct, assemble it in sequence. That's it!
Read more