XhorseStore

  Xhorse VVDI BIMTOOL PRO is able to do BMW mileage adjustment via file. Support system including EWS1/EWS2, EWS3, EWS4, CAS1, CAS2, CAS3, CAS3+, CAS4(0L15Y), CAS4(5M48H), CAS3+ encrypt version select CAS3+ type. How to Change BMW KM via File? Change KM for EWS/CAS Load EEPROM dump, input new KM value, press button "Change KM". Save new EEPROM dump, then write back it to EEPROM. CAS1/CAS2/CAS3/CAS3+ Change KM Steps Record the KM info displayed in instrument, take instrument away from car to avoid synchronizing KM with CAS automatically. Set CAS KM to 0(you can do this via OBD or EEPROM dump, select correct CAS version). Read instrument EEPROM dump by VVDI BMW programmer then save EEPROM dump you read, usually use M35080 chip. Select: File Change KM >> M35808(Instrument) and load EEPROM dump saved in step 3. *Attention: this type instrument have 2 algorithm for KM: Algorithm 1 & Algorithm 2. You need to try different algorithms to check the O...

  Xhorse XKGHG1EN Masker Garage Remote is special design that can manually switch over 20 frequencies available. The frequency edition can be set by VVDI key tool series device like VVDI Key Tool Max or Key Tool Max PRO . This article guides to set garage remote frequency for beginners. How to set Xhorse garage remote frequency? Why to set frequency? There are many different brands of carage remotes in market. Different manufactures maybe with different frequency. If the original remote and Xhorse carage remote frequency are different, it may cause remote cloning failed or even successful cloning but with too short working distance. Xhorse carage remote supports to set frequency function(20 frequency point) to ensure frequency is same as the original one. How to set frequency? Enter set frequency mode: Press and hold the "Lock"&"Pause" buttons at same time, remote LED light is on. Keep pressing 2 buttons until the remote LED light is off, t...

  Problem: The Xhorse Dolphin XP-005L gives an error message:" ERROR CODE: 56. Cutter short circuit, please check cutter electrical conductivity". The message could be gone if I turned off the key cutting machine for an hour before, but it does not work now. I've cleaned all metal shavings from the clamp. What's going on? Please help. Solution Dissemble Dolphin 2 machine to clean the electric lead of milling cutter, this problem can be solved. Technical Support www.xhorsestore.co.uk

  Xhorse XKGHG1EN Masker Garage Remote is the newest Xhorse slide key, which supports code deleting, remote cloning, frequency setting and data recovery. Slide down its cover, we can see the LED light, Up/Down/Lock/Pause button. Xhorse Masker Garage Remote Introduction Video: https://www.youtube.com/watch?v=nwXO00hR6Uo How to check code? To make sure the code is cleared, we need to check the carage remote status before remote cloning. As long as you keep pressing any key button, the LED light is always on, which means the code hasn't been deleted. How to delete code? Press and hold "Up & Down" buttons at the same time. We can see the LED light turns on. When the light tuns off, release all buttons. Press and hold "Pause" button until the light goes off. Then release the button. Now the light will flash once then go out quickly when pressing any button on carage remote. It means the code is deleted. How to do remote cloning? Make sure...

  Question: Why the Xhorse VVDI Key Tool Max is unable to control BMW X3 2014 VIN? It failed to read when I was putting the key into slot. Please advice. Answer It's suggested to use Xhorse VVDI Key Tool Plus Pad or VVDI BIMTOOL PRO tool to program BMW keys. Cause they both have wider applicability and specialty for BMW immo programming. Technical Support www.xhorsestore.co.uk

Problem: The Xhorse VVDI Key Tool Max PRO is failed to generate CHANGFENG 433 with XKGHG1EN Masker Carage Remote . It always gave the prompt: "Please put in X wire remote, XN wireless remote or XT superchip-remote." What's the problem? Please advise. Solution Considering the XKGHG1ENCarage Remote is a wire remote. Please connect to VVDI Key Tool Max PRO via cable for generation. Please DO NOT put battery when generating remote. Thanks to www.xhorsestore.co.uk , problem was solved.