XhorseStore

  Xhorse XEDS01EN Super Remote has a built-in super chip, it can be used for all possible IDs. So here comes the question, can it be used for 2021 Suzuki S Presso? I did not find it in the option of Key Tool Max . The reply is: Xhorse XEDS01EN Super Remote can support 2021 Suzuki S Presso. But since VVDI Key Tool Max does not have Suzuki S Presso option, so we can select S-Cross SX4 instead, which also has wireless function & ID47. Vehicle remote >> Suzuki >> S-Cross SX4 ID47 2015 After this you can add keys for 2021 Suzuki S Presso using Xhorse VVDI Key Tool Plus . Original Xhorse Tool Supplier: https://www.xhorsestore.co.uk/

 Hello guys, I'm here on a 2015 Hyundai ix35, and next I'm gonna use Xhorse VVDI Key Tool Plus to add new keys for it via OBD. Very easy and simple process that only takes 1 minute. Procedure Plug VVDI Key Tool Plus diagnostic cable into OBD. Immo programming >> Hyundai >> Select by type >> Remote system >> 16PIN >> Type 1 >> Start programming >> Remote key adaptation Connect OBD, insert the key and turn on ignition switch, then turn off and remove the key! Press and hold the LOCK or UNLOCK button of the need to match remote for 1s. (If the matching fails, press and hold the LOCK and UNLOCK buttons at the same time!) xhorse 1 key has been programmed successfully! Press "Yes" to program next one, just repeat same operations. 2 keys has been programmed successfully! Press "No" to complete. Now test the new keys, both remote can work well. Done. This is how to add 2015 Hyundai ix35 keys with Xh...

  Xhorse VVDI Key Tool Plus Pad is able to add a smart key for 2015 Lamborghini Huracan successfully. Need to disassemble BCM2 module from vehicle for immo reading firstly. Then re-install back to the vehicle to program new keys by OBD. Tools in Need VVDI Key Tool Plus BCM2 Solder-free Adapter BCM2 module Operation Path: Immo programming >> Audi >> Select by type >> Fifth immobilizer system After successfully read & save immo data, install the BCM2 module back to car. Plug Key Tool Plus to OBD to continue key adding. Please input the number of keys to be learned: 2 Load BCM2 data >> Select and open immo data file Load data success. Insert working key into ignition(or nearby ignition coil) and switch on before continue. If lost all working key, insert dealer key into ignition(or nearby ignition coil). Open the headlight, and step on the brake before continue. We can see the key adding status on dashboard. Done. www.xhorsest...

 This is a guide on how to bind & activate VVDI BEE Key Tool Lite in Xhorse app. Make sure you've registered a Xhorse account before that. Procedure Connect VVDI BEE Key Tool Lite to smart phone. Open Xhorse app: click "Connect". It'll give a welcome page: Hello, thank you for buying and using Key Tool Lite . For better use of product functions, need to active and bind the device before the first time. Start To Set >> Send Please combine email, cellphone account combined device and bonus points will be synchronized to email account! Click "Skip". Enter the security code. Click "Combine device". Warnings After device combined to account, account will share this device bonus points. Part of devices support to share function. Click "Combine device" again. Combined device success. Device activation success. Now you can start to use Xhorse VVDI Key Tool Lite. www.xhorsestore.co.uk

  Problem: I've updated XHORSE MVCI PRO J2534 firmware and software to latest, but I am still getting the attention: "Sync authorization 2 failed! Error code: ff02". The firmware is 1.20 and software is 2.0.1. What's the problem? Solution Please go for synchronization firstly: Device management >> Connect >> Read authorization >> Update authorization The problem will be solved. Technical Support www.xhorsestore.co.uk

  Xhorse VVDI Bee Key Tool Lite is a new device that supports to generate remote on Android phones. Besides, it also supports to generate and clone transponder, detect remote frequency, clone IC/ID, unlock Toyota smart key, etc. Read this post to learn how to use. Xhorse VVDI Key Tool Lite Configuration Key Slot Coil: 1) Remote frequency detection; 2) Chip clone collection; 3) Chip and remote reading coil(125Khz, 134KHz). IC Card Identification Working Status Indicator Light: Flash — upgrade mode, Always On — working mode Connect to Phone TYPE-C Interface Remote Programming Cable Port Remote Programming Cable Xhorse VVDI Key Tool Lite Connection Method How to power on? Insert TYPE-C cable; Allow Xhorse app to access thethe phone via USB; Connect the device. How to power off? Disconnect the TYPE-C cable. Note: If there is a prompt on the right side of the interface, open the phone settings and turn on the OTG connection switch. Main function 1: Generate Re...

 This is Xhorse MVCI PRO J2534 Cable Manual covering features, download and installation.Xhorse MVCI PROis a perfect replacement for the original testing equipment to do factory-level diagnosis and programming. Supports VW, Toyota, Honda, Ford and other automobile manufacturers. New Features Download Xhorse MVCI PRO J2534 Driver free download link: https://mega.nz/file/MuoiBJZa#MjmQNzgll4pJEERnq1v__sHx6n3C9nr-cMwJqChNPAs Software Size: 52.2MB Language: English, Chinese Operating System: Win7, Win10 * Please ensure you've installed the original diagnostic software that supports J2534 on computer. If not, download from original manufacturer's website or third party. Installation Select language >> Next >> Next >> Install >> Finish How to use Xhorse MVCI PRO J2534? Connect MVCI PRO J2534 Cable, Car OBD port and computer, click "Connect". Here we can check the device info including firmware version, serial number, etc. ...

 Xhorse had did some upgrading on the M5 Clamp a couple of days ago. M5 clamp is now compatible with these automatic key cutting machines: Condor XC-Mini Plus II / XC-Mini Plus / XC-Mini(KM03), Dolphin XP-005L / XP-005 . M5 clamp perfectly integrates the functions of M1 and M2 clamps. It supports 2 track external, double side key, 4 track internal, 4 track external, channel trak key types. And it can also handle dimple key cutting when used with Condor XC-Mini Plus II. The thin, narrow, and short keys, as well as the special HU162T keys are perfectly supported by the M5 clamp. It also comes with a thoughtful design. It does not require an auxiliary key blank to clamp HU162Tkeys or elevate the key blank when cutting a Toyota single sided key. Additionally, the M5 clamp is designed to offer a non-calibrating using experience, which means you don’t need to calibrate the clamp anymore while working. How to clamp a key on M5 clamp? When Xhorse M5 Clamp is on side ...